1 Which of the following best describes an alternating voltage (ac voltage)?
A A voltage that stays constant with time B A voltage that varies like a sine function with time C A voltage that decreases linearly with time D A voltage that changes only direction once
उत्तर देखें
सही उत्तर: B. A voltage that varies like a sine function with time
The mains supply is a voltage that varies sinusoidally with time. Such a voltage is called an alternating voltage.
2 The main reason for preferring ac voltage over dc voltage for power distribution is that:
A AC voltages are always smaller than dc voltages B AC cannot cause heating in wires C AC voltages can be easily and efficiently converted from one value to another by transformers D AC voltages need no wires
उत्तर देखें
सही उत्तर: C. AC voltages can be easily and efficiently converted from one value to another by transformers
Transformers can step ac voltage up or down efficiently, and electrical energy can then be transmitted economically over long distances.
3 Tuning a radio to a favourite station makes use of which property of ac circuits?
A Resonance B Rectification C Eddy currents D Hysteresis
उत्तर देखें
Tuning varies the capacitance so that the circuit's resonant frequency matches the frequency of the received radio signal.
4 For an ac voltage v = vₘ sin ωt applied to a pure resistor R, the current amplitude is:
A iₘ = vₘR B iₘ = R/vₘ C iₘ = vₘ/R D iₘ = vₘ/R²
उत्तर देखें
Kirchhoff's loop rule gives vₘ sin ωt = iR, so iₘ = vₘ/R. This is Ohm's law, valid for ac and dc.
5 In a purely resistive ac circuit, the phase difference between voltage and current is:
A π/2 B π C π/4 D Zero
उत्तर देखें
Voltage and current reach their zero, minimum and maximum values at the same time, so they are in phase.
6 The average current over one complete cycle in an ac circuit with sinusoidal current is:
A iₘ/√2 B Zero C iₘ D iₘ/2
उत्तर देखें
Positive and negative half cycles cancel, so the average current over a full cycle is zero.
7 Although the average ac current is zero, there is Joule heating in a resistor because:
A Heating depends on i², which is always positive B Heating depends on i, which is always positive C The resistance changes sign D The voltage is always positive
उत्तर देखें
सही उत्तर: A. Heating depends on i², which is always positive
Joule heating is i²R, and i² is positive whether i is positive or negative.
8 The average value of sin²ωt over one complete cycle is:
A 0 B 1 C 1/2 D 1/√2
उत्तर देखें
sin²ωt = ½(1 − cos 2ωt) and ⟨cos 2ωt⟩ = 0, so ⟨sin²ωt⟩ = 1/2.
9 The average power dissipated in a resistor carrying i = iₘ sin ωt is:
A iₘ²R B ½ iₘ²R C 2iₘ²R D iₘR/2
उत्तर देखें
p = iₘ²R sin²ωt, and averaging with ⟨sin²ωt⟩ = 1/2 gives ½ iₘ²R.
10 The rms current I is related to the peak current iₘ by:
A I = √2 iₘ B I = iₘ/2 C I = 2iₘ D I = iₘ/√2
उत्तर देखें
I = √(i²) = √(½ iₘ²) = iₘ/√2 ≈ 0.707 iₘ.
11 Which expression gives the average ac power in terms of rms values for a resistor?
A P = IV/2 B P = I²R C P = I²/R D P = V/R²
उत्तर देखें
With rms values, P = ½ iₘ²R = I²R, the same form as the dc power.
12 The household line voltage of 220 V (rms) has a peak value of about:
A 155 V B 220 V C 311 V D 440 V
उत्तर देखें
vₘ = √2 V = 1.414 × 220 ≈ 311 V.
13 A 100 W bulb is rated for a 220 V supply. Its resistance is:
A 484 Ω B 2.2 Ω C 242 Ω D 968 Ω
उत्तर देखें
R = V²/P = (220)²/100 = 484 Ω.
14 The rms current through the 100 W, 220 V bulb is about:
A 0.227 A B 0.454 A C 0.909 A D 2.2 A
उत्तर देखें
I = P/V = 100/220 ≈ 0.454 A.
15 The ac ampere is defined for an alternating current using which property?
A Mutual attraction of parallel wires B Magnetic effect C Joule heating effect, independent of current direction D Chemical effect
उत्तर देखें
सही उत्तर: C. Joule heating effect, independent of current direction
Attraction between wires would average to zero for ac. One ampere rms of ac produces the same average heating as one ampere of dc.
16 In a phasor diagram, the length of a phasor represents:
A The instantaneous value of the quantity B The rms value only C The average value D The amplitude (peak value) of the quantity
उत्तर देखें
सही उत्तर: D. The amplitude (peak value) of the quantity
The magnitudes of phasors V and I represent the amplitudes vₘ and iₘ. Their vertical components give instantaneous values.
17 A phasor is a vector that:
A Is fixed along the horizontal axis B Rotates about the origin with angular speed ω C Rotates with angular speed 2ω D Oscillates along a line
उत्तर देखें
सही उत्तर: B. Rotates about the origin with angular speed ω
A phasor rotates about the origin with angular speed ω, and its vertical component represents the sinusoidal quantity.
18 In an ac circuit with a pure inductor, the current:
A Leads the voltage by π/2 B Is in phase with the voltage C Lags the voltage by π/2 D Lags the voltage by π
उत्तर देखें
सही उत्तर: C. Lags the voltage by π/2
i = iₘ sin(ωt − π/2), so the current lags the voltage by π/2, one-quarter of a cycle.
19 The inductive reactance of an inductor L at angular frequency ω is:
A 1/ωL B ωL C L/ω D ω/L
उत्तर देखें
X_L = ωL. It is directly proportional to the inductance and the frequency.
20 The SI unit of inductive reactance is:
A Henry B Farad C Ohm D Weber
उत्तर देखें
Reactance has the same dimensions as resistance, and its SI unit is the ohm (Ω).
21 A pure inductor of 25.0 mH is connected to a 220 V, 50 Hz source. The inductive reactance is about:
A 7.85 Ω B 78.5 Ω C 1.25 Ω D 0.785 Ω
उत्तर देखें
X_L = 2πνL = 2 × 3.14 × 50 × 25×10⁻³ ≈ 7.85 Ω.
22 For the same 25.0 mH inductor on a 220 V supply, the rms current is about:
A 2.8 A B 280 A C 28 A D 0.28 A
उत्तर देखें
I = V/X_L = 220/7.85 ≈ 28 A.
23 The average power supplied to a pure inductor over one complete cycle is:
A iₘvₘ/2 B Maximum C iₘvₘ D Zero
उत्तर देखें
p_L = −(iₘvₘ/2) sin 2ωt, whose average over a full cycle is zero.
24 For an ac voltage applied to a pure capacitor, the current:
A Lags the voltage by π/2 B Leads the voltage by π/2 C Is in phase with the voltage D Is zero
उत्तर देखें
सही उत्तर: B. Leads the voltage by π/2
i = iₘ sin(ωt + π/2), so the current is π/2 ahead of the voltage.
25 The capacitive reactance of a capacitor C at angular frequency ω is:
A ωC B C/ω C ω/C D 1/ωC
उत्तर देखें
X_C = 1/ωC, so it is inversely proportional to frequency and capacitance.
26 A 15.0 μF capacitor is connected to a 220 V, 50 Hz source. The capacitive reactance is about:
A 21.2 Ω B 212 Ω C 2120 Ω D 106 Ω
उत्तर देखें
X_C = 1/(2π × 50 × 15×10⁻⁶) ≈ 212 Ω.
27 For the 15.0 μF capacitor on a 220 V, 50 Hz source, the peak current is about:
A 1.04 A B 2.08 A C 0.735 A D 1.47 A
उत्तर देखें
I = 220/212 ≈ 1.04 A, so iₘ = √2 I ≈ 1.41 × 1.04 ≈ 1.47 A.
28 If the source frequency in a purely capacitive circuit is doubled, the current:
A Is halved B Is doubled C Remains unchanged D Becomes four times
उत्तर देखें
X_C ∝ 1/ν, so doubling the frequency halves X_C and doubles the current.
29 A lamp is connected in series with a capacitor. With a dc source, the lamp:
A Glows steadily B Glows dimly C Glows brightly at first, then dims D Does not glow after the capacitor is charged
उत्तर देखें
सही उत्तर: D. Does not glow after the capacitor is charged
After the capacitor is charged no dc current flows. With ac the capacitor offers reactance 1/ωC and the lamp glows.
30 In a lamp–capacitor series circuit on ac, reducing the capacitance makes the lamp:
A Shine more brightly B Shine less brightly C Stop glowing at once D Shine exactly the same
उत्तर देखें
सही उत्तर: B. Shine less brightly
Reducing C increases the reactance 1/ωC, which reduces the current.
31 A light bulb and an open-coil inductor are in series with an ac source. When an iron rod is inserted into the coil, the glow of the bulb:
A Increases B Is unchanged C Decreases D Becomes steady dc-like
उत्तर देखें
The iron raises the inductance and reactance, so more of the applied voltage appears across the inductor and less across the bulb.
32 In a series LCR circuit, the same quantity common to R, L and C at every instant is:
A Voltage B Current C Power D Phase of voltage
उत्तर देखें
The elements are in series, so the current has the same amplitude and phase through each.
33 In a series LCR circuit, the voltage across the inductor V_L leads the current by:
A π/2 B Zero C π D π/4
उत्तर देखें
V_R is parallel to I, V_C is π/2 behind I, and V_L is π/2 ahead of I.
34 The impedance of a series LCR circuit is:
A Z = R + X_C + X_L B Z = √(R² + (X_C − X_L)²) C Z = √(R² + X_C² + X_L²) D Z = R + (X_C − X_L)
उत्तर देखें
सही उत्तर: B. Z = √(R² + (X_C − X_L)²)
From the right-angled phasor triangle, vₘ² = vₘR² + (v_Cm − v_Lm)², which gives Z = √(R² + (X_C − X_L)²).
35 The phase angle φ in a series LCR circuit is given by:
A tan φ = R/(X_C − X_L) B tan φ = (X_C + X_L)/R C tan φ = (X_C − X_L)/R D tan φ = R(X_C − X_L)
उत्तर देखें
सही उत्तर: C. tan φ = (X_C − X_L)/R
tan φ = (v_Cm − v_Lm)/v_Rm = (X_C − X_L)/R.
36 In a series LCR circuit, if X_C < X_L, the circuit is predominantly:
A Capacitive, and the current leads the voltage B Resistive, and the current is in phase C Capacitive, and the current lags the voltage D Inductive, and the current lags the source voltage
उत्तर देखें
सही उत्तर: D. Inductive, and the current lags the source voltage
If X_C < X_L, φ is negative and the circuit is predominantly inductive, so the current lags.
37 A 200 Ω resistor and a 15.0 μF capacitor are in series on a 220 V, 50 Hz source. The impedance is about:
A 412 Ω B 212 Ω C 200 Ω D 292 Ω
उत्तर देखें
Z = √(200² + 212.3²) ≈ 291.7 Ω.
38 In the same RC circuit (R = 200 Ω, C = 15.0 μF, 220 V), the rms current is about:
A 0.755 A B 1.1 A C 0.5 A D 1.51 A
उत्तर देखें
I = V/Z = 220/291.5 ≈ 0.755 A.
39 In the same RC circuit, V_R + V_C (algebraic) is about 311 V, which exceeds 220 V. This paradox is resolved because:
A The source voltage is wrongly measured B V_R and V_C are π/2 out of phase and must be added by the Pythagorean theorem C Capacitors create extra voltage D V_R and V_C are in phase
उत्तर देखें
सही उत्तर: B. V_R and V_C are π/2 out of phase and must be added by the Pythagorean theorem
√(V_R² + V_C²) = √(151² + 160.3²) ≈ 220 V, equal to the source voltage.
40 The resonant angular frequency of a series LCR circuit is:
A ω₀ = LC B ω₀ = 1/(LC) C ω₀ = 1/√(LC) D ω₀ = √(L/C)
उत्तर देखें
सही उत्तर: C. ω₀ = 1/√(LC)
Resonance occurs when X_C = X_L, i.e. 1/ω₀C = ω₀L, giving ω₀ = 1/√(LC).
41 At resonance in a series LCR circuit, the impedance is:
A Maximum B Equal to R, its minimum value C Zero D Equal to X_L + X_C
उत्तर देखें
सही उत्तर: B. Equal to R, its minimum value
Since X_C = X_L, Z = √(R² + 0²) = R, the minimum impedance.
42 At resonance in a series LCR circuit, the current amplitude is:
A vₘ/R, its maximum value B vₘ/Z with Z large C Zero D vₘ/(X_L + X_C)
उत्तर देखें
सही उत्तर: A. vₘ/R, its maximum value
With Z = R, iₘ = vₘ/R, which is the maximum current.
43 For L = 1.00 mH and C = 1.00 nF, the resonant angular frequency is:
A 1.00×10³ rad/s B 1.00×10⁹ rad/s C 1.00×10⁶ rad/s D 1.00×10⁻⁶ rad/s
उत्तर देखें
सही उत्तर: C. 1.00×10⁶ rad/s
ω₀ = 1/√(10⁻³ × 10⁻⁹) = 1/√(10⁻¹²) = 10⁶ rad/s.
44 In the resonance curves for R = 100 Ω and R = 200 Ω with the same vₘ, the peak current at resonance for R = 100 Ω is:
A Half that for R = 200 Ω B Equal to that for R = 200 Ω C Twice that for R = 200 Ω D Four times that for R = 200 Ω
उत्तर देखें
सही उत्तर: C. Twice that for R = 200 Ω
At resonance iₘ = vₘ/R, so halving R doubles the peak current.
45 Resonance cannot occur in an RL or RC circuit because:
A The resistance is too large B Both L and C are needed so that their voltages can cancel C The frequency is fixed D AC cannot flow in them
उत्तर देखें
सही उत्तर: B. Both L and C are needed so that their voltages can cancel
Resonance requires both L and C, whose voltages are out of phase and cancel. With only one, no cancellation is possible.
46 In the tuning circuit of a radio, tuning to a station is done by varying:
A The resistance B The capacitance so that resonant frequency matches the signal C The supply voltage D The number of turns of the antenna
उत्तर देखें
सही उत्तर: B. The capacitance so that resonant frequency matches the signal
The capacitance is varied so that the circuit's resonant frequency nearly equals the received signal frequency.
47 The average power dissipated in an LCR circuit is given by:
A P = VI sin φ B P = VI C P = VI cos φ D P = VI tan φ
उत्तर देखें
सही उत्तर: C. P = VI cos φ
P = (vₘiₘ/2) cos φ = VI cos φ, where cos φ is the power factor.
48 The power factor of a purely inductive or capacitive circuit is:
A 1 B 0 C 0.5 D Infinite
उत्तर देखें
φ = π/2, so cos φ = 0 and no power is dissipated. The current is called wattless current.
49 Power in an LCR circuit is dissipated only in:
A The inductor B The capacitor C The resistor D Both L and C
उत्तर देखें
सही उत्तर: C. The resistor
Pure inductors and capacitors do not dissipate power on average, so only the resistor dissipates energy.
50 A low power factor in power transmission lines implies:
A Smaller current for a given power B Large I²R power loss C Lower voltage D No loss
उत्तर देखें
सही उत्तर: B. Large I²R power loss
For a given power and voltage, a small cos φ requires a larger current, which causes a large I²R loss.
51 A series LCR circuit has R = 3 Ω, L = 25.48 mH, C = 796 μF at 50 Hz. The impedance is:
A 11 Ω B 5 Ω C 3 Ω D 7 Ω
उत्तर देखें
X_L = 8 Ω, X_C = 4 Ω, so Z = √(3² + (8 − 4)²) = 5 Ω.
52 For the same circuit (R = 3 Ω, X_L = 8 Ω, X_C = 4 Ω), the power factor is:
A 0.8 B 0.5 C 0.6 D 1.0
उत्तर देखें
53 For the same circuit with peak voltage 283 V, the power dissipated is about:
A 4800 W B 2400 W C 1200 W D 13.35 kW
उत्तर देखें
I = (283/5)/√2 = 40 A, so P = I²R = 1600 × 3 = 4800 W.
54 For the circuit with L = 25.48 mH and C = 796 μF, the resonant angular frequency is about:
A 222 rad/s B 50 rad/s C 314 rad/s D 35.4 rad/s
उत्तर देखें
ω₀ = 1/√(25.48×10⁻³ × 796×10⁻⁶) ≈ 222 rad/s.
55 At resonance, the rms current in the circuit (R = 3 Ω, peak voltage 283 V) is about:
A 40 A B 94 A C 33.4 A D 66.7 A
उत्तर देखें
I = V/R = (283/√2)/3 ≈ 66.7 A.
56 A metal detector at an airport works on the principle of:
A Electromagnetic induction in dc circuits B Resonance in ac circuits C Rectification D Photoelectric effect
उत्तर देखें
सही उत्तर: B. Resonance in ac circuits
Metal changes the impedance of the tuned coil–capacitor circuit, which changes the current and triggers the alarm.
57 A transformer works on the principle of:
A Self-induction only B Mutual induction C Resonance D Joule heating
उत्तर देखें
सही उत्तर: B. Mutual induction
A changing flux from the primary links the secondary and induces an emf in it, which is mutual induction.
58 For an ideal transformer, the ratio of secondary to primary voltage is:
A N_p/N_s B N_s/N_p C (N_s/N_p)² D N_s × N_p
उत्तर देखें
v_s/v_p = N_s/N_p, from the equal flux per turn in both coils.
59 A transformer has 100 primary turns and 200 secondary turns. A 220 V, 10 A input gives an output of:
A 110 V, 20 A B 440 V, 5.0 A C 440 V, 20 A D 220 V, 10 A
उत्तर देखें
सही उत्तर: B. 440 V, 5.0 A
V_s = 2 × 220 = 440 V and I_s = (100/200) × 10 = 5 A. This is a step-up transformer.
60 In a step-down transformer:
A N_s > N_p and I_s < I_p B N_s < N_p and V_s > V_p C N_s < N_p, V_s < V_p and I_s > I_p D N_s = N_p
उत्तर देखें
सही उत्तर: C. N_s < N_p, V_s < V_p and I_s > I_p
Fewer secondary turns lower the voltage and raise the current.
61 Which energy loss in a transformer is reduced by using a laminated core?
A Flux leakage B Resistance of windings C Hysteresis D Eddy currents
उत्तर देखें
सही उत्तर: D. Eddy currents
Alternating flux induces eddy currents in the iron core. Lamination reduces them.
62 Transformers use thick wire in high-current, low-voltage windings to reduce:
A Eddy currents B Hysteresis loss C Flux leakage D Heat loss due to winding resistance
उत्तर देखें
सही उत्तर: D. Heat loss due to winding resistance
Thick wire has lower resistance, which minimises the I²R heating in the windings.
63 Large-scale power transmission steps up the voltage at the generator end so that:
A Current is reduced and I²R loss is cut down B Current increases C Power increases D Frequency increases
उत्तर देखें
सही उत्तर: A. Current is reduced and I²R loss is cut down
For a given power, higher voltage means lower current, and so a smaller I²R loss in the lines.
64 A 100 Ω resistor is connected to a 220 V, 50 Hz ac supply. The rms current is:
A 1.1 A B 3.1 A C 2.2 A D 0.45 A
उत्तर देखें
I = V/R = 220/100 = 2.2 A.
65 The net power consumed by that 100 Ω resistor over a full cycle is about:
A 484 W B 242 W C 968 W D 220 W
उत्तर देखें
P = I²R = (2.2)² × 100 = 484 W.
66 The peak voltage of an ac supply is 300 V. The rms voltage is about:
A 150 V B 300 V C 424 V D 212 V
उत्तर देखें
V = vₘ/√2 = 300/1.414 ≈ 212 V.
67 The rms value of current in an ac circuit is 10 A. The peak current is about:
A 7.07 A B 14.1 A C 20 A D 5 A
उत्तर देखें
68 A 44 mH inductor is connected to a 220 V, 50 Hz supply. The rms current is about:
A 15.9 A B 1.59 A C 5 A D 22.5 A
उत्तर देखें
X_L = 2π × 50 × 0.044 ≈ 13.8 Ω, so I = 220/13.8 ≈ 15.9 A.
69 A 60 μF capacitor is connected to a 110 V, 60 Hz supply. The rms current is about:
A 1.24 A B 2.49 A C 0.62 A D 24.9 A
उत्तर देखें
X_C = 1/(2π × 60 × 60×10⁻⁶) ≈ 44.2 Ω, so I = 110/44.2 ≈ 2.49 A.
70 The net power absorbed by the pure inductor and pure capacitor circuits over a complete cycle is:
A Maximum B Equal to VI C Equal to I²R D Zero
उत्तर देखें
The phase difference is π/2, so cos φ = 0. Energy is alternately stored and returned.
71 A charged 30 μF capacitor is connected to a 27 mH inductor. The angular frequency of free oscillations is about:
A 1.11×10³ rad/s B 1.11×10⁶ rad/s C 3.7×10² rad/s D 111 rad/s
उत्तर देखें
सही उत्तर: A. 1.11×10³ rad/s
ω = 1/√(LC) = 1/√(27×10⁻³ × 30×10⁻⁶) = 1/√(8.1×10⁻⁷) ≈ 1.11×10³ rad/s.
72 A series LCR circuit with R = 20 Ω, L = 1.5 H, C = 35 μF is connected to a 200 V variable-frequency supply at the natural frequency. The average power transferred is:
A 1000 W B 4000 W C 2000 W D 400 W
उत्तर देखें
At resonance Z = R, so I = 200/20 = 10 A and P = I²R = 100 × 20 = 2000 W.
73 A series LCR circuit has L = 5.0 H, C = 80 μF, R = 40 Ω on a 230 V source. The resonant angular frequency is:
A 25 rad/s B 50 rad/s C 100 rad/s D 12.5 rad/s
उत्तर देखें
ω₀ = 1/√(5 × 80×10⁻⁶) = 1/√(4×10⁻⁴) = 1/0.02 = 50 rad/s.
74 For the circuit with L = 5.0 H, C = 80 μF, R = 40 Ω and a 230 V source, the amplitude of current at resonance is about:
A 8.1 A B 5.75 A C 4.1 A D 2.9 A
उत्तर देखें
Z = R = 40 Ω, so iₘ = √2 × 230/40 ≈ 8.1 A.
75 For the same circuit at resonance, the rms potential drop across the inductor is about:
A 230 V B 1437.5 V C 575 V D 40.6 V
उत्तर देखें
I_rms = 230/40 = 5.75 A and X_L = ω₀L = 250 Ω, so V_L = 5.75 × 250 = 1437.5 V. V_C is equal in magnitude and opposite in phase, so the LC drop is zero.
76 In the quality factor expression for a series RLC circuit, Q equals:
A R/(ω₀L) B ω₀L/R C ω₀LR D ω₀²LC
उत्तर देखें
The chapter's table gives Q = ω₀L/R = 1/(ω₀CR). Q is dimensionless.
77 According to Points to Ponder, if the rms voltage at an outlet is 240 V, its amplitude is about:
A 170 V B 240 V C 340 V D 480 V
उत्तर देखें
78 The roles of input and output in a motor and a generator are:
A Same B Reversed C Both mechanical D Both electrical
उत्तर देखें
A motor takes electrical input and gives mechanical output. A generator takes mechanical input and gives electrical output.
79 A step-up transformer changing low voltage to high voltage does not violate energy conservation because:
A The current is reduced by the same proportion B Power is created in the core C Frequency is doubled D The core stores energy
उत्तर देखें
सही उत्तर: A. The current is reduced by the same proportion
Voltage increases by the turns ratio and current decreases by the same factor, so power stays the same.