Are you looking for JAC Class 12 Physics Chapter 14 “Semiconductor Electronics” MCQs (Objective Questions) with Answers? You are at the right place! On JAC Exam Prep, you will find important Multiple Choice Questions (MCQs) with Answers from the “Semiconductor Electronics” chapter. These questions are prepared according to the latest NCERT syllabus and with a focus on the Jharkhand Academic Council (JAC) examination.
These Semiconductor Electronics MCQs cover important topics such as energy bands in solids, conductors, insulators, semiconductors, intrinsic and extrinsic semiconductors, p-type and n-type semiconductors, p-n junction diode, forward and reverse bias, diode characteristics, rectifiers, and semiconductor devices. By practising these questions, students can revise the chapter effectively, strengthen their conceptual understanding, and perform better in the JAC Class 12 Annual Examination.
Before the discovery of the transistor in 1948, electronic devices were mostly
सही उत्तर:B. vacuum tubes, also called valves
Before 1948 the basic devices were vacuum tubes such as the diode, triode, tetrode and pentode.
2
How many electrodes does a vacuum triode have?
सही उत्तर:D. 3
A triode has three electrodes: cathode, plate and grid.
3
For the same input frequency of \(50\ \text{Hz}\), the output frequency of a full-wave rectifier is
सही उत्तर:A. \(100\ \text{Hz}\)
A full-wave rectifier gives an output pulse in every half cycle, so the output frequency is twice the input frequency, \(100\ \text{Hz}\).
4
A circuit with a single diode in series with a load resistor, fed by an ac source, is called a
सही उत्तर:C. half-wave rectifier
With one diode, current flows only in the half cycles when the diode is forward biased, so it is a half-wave rectifier.
5
Which of the following is a disadvantage of vacuum tubes compared with semiconductor devices?
सही उत्तर:D. They are bulky, consume high power and have limited life and low reliability
Vacuum tubes are bulky, power-hungry, operate at high voltages and have limited life and low reliability.
6
In semiconductor devices, the supply and flow of charge carriers take place
सही उत्तर:A. within the solid itself
In semiconductor devices the charge carriers are present in and flow through the solid, so no heating or evacuated space is required.
7
A naturally occurring crystal used with a metal point contact as a detector of radio waves was
सही उत्तर:C. galena, which is lead sulphide
Galena, a crystal of lead sulphide \(\text{PbS}\), was used as a radio-wave detector.
8
The resistivity of metals lies approximately in the range
सही उत्तर:B. \(10^{-2}\) to \(10^{-8}\ \Omega\ \text{m}\)
Metals have very low resistivity, about \(10^{-2}\) to \(10^{-8}\ \Omega\ \text{m}\).
9
The resistivity of insulators lies approximately in the range
सही उत्तर:C. \(10^{11}\) to \(10^{19}\ \Omega\ \text{m}\)
Insulators have very high resistivity, about \(10^{11}\) to \(10^{19}\ \Omega\ \text{m}\).
10
The conductivity of semiconductors lies approximately in the range
सही उत्तर:A. \(10^{5}\) to \(10^{-6}\ \text{S m}^{-1}\)
Semiconductors have conductivity intermediate between metals and insulators, about \(10^{5}\) to \(10^{-6}\ \text{S m}^{-1}\).
11
Which pair consists of elemental semiconductors?
सही उत्तर:D. Si and Ge
Silicon and germanium are the elemental semiconductors; the others are compound semiconductors.
12
A full-wave rectifier using two diodes requires a
सही उत्तर:B. centre-tap transformer
The secondary needs a centre tapping so that each diode rectifies one half of the cycle.
13
The energy band that contains the energy levels of the valence electrons is called the
सही उत्तर:A. valence band
By definition, the band that includes the energy levels of the valence electrons is the valence band.
14
In a metal, the valence band and the conduction band
सही उत्तर:C. overlap, or the conduction band is partially filled
In metals the bands overlap (or one is partially filled), so a large number of electrons are available for conduction.
15
The energy gap \(E_g\) of an insulator is
सही उत्तर:B. greater than \(3\ \text{eV}\)
In an insulator \(E_g>3\ \text{eV}\), so electrons cannot be thermally excited to the conduction band.
16
Why does a semiconductor conduct slightly at room temperature?
सही उत्तर:D. Its small band gap lets some valence electrons gain enough thermal energy to enter the conduction band
For \(E_g<3\ \text{eV}\), some valence electrons acquire enough energy at room temperature to cross the gap.
17
A Si or Ge crystal containing \(N\) atoms has how many valence electrons in total?
सही उत्तर:D. \(4N\)
Each atom has 4 outer electrons, giving \(4N\) in total, which fill \(4N\) of the \(8N\) available states.
18
In a Si crystal of \(N\) atoms, the \(8N\) states split into two bands separated by \(E_g\). The conduction band contains how many states?
सही उत्तर:B. \(4N\)
The \(8N\) states split into two bands of \(4N\) states each, the valence band and the conduction band.
19
At absolute zero, in a Si or Ge crystal
सही उत्तर:C. the valence band is completely filled and the conduction band is completely empty
At \(0\ \text{K}\) the \(4N\) valence electrons fill the valence band and the conduction band is empty.
20
Si and Ge have the same crystal structure as diamond, which is described as
सही उत्तर:A. a diamond-like structure
Si and Ge crystallise in the diamond-like structure.
21
In the diamond-like lattice of Si or Ge, each atom is surrounded by how many nearest neighbours?
सही उत्तर:B. 4
Each atom has four nearest neighbours, with which it shares its four valence electrons.
22
In a Si crystal, the shared pair of electrons between two neighbouring atoms forms a
सही उत्तर:D. covalent bond
Shared electron pairs hold neighbouring atoms together as covalent (valence) bonds.
23
A vacancy in a covalent bond, which behaves like a free particle with effective positive charge, is called a
सही उत्तर:A. hole
The vacancy left by a freed electron has an effective charge \(+q\) and is called a hole.
24
In an intrinsic semiconductor, the number of free electrons \(n_e\), the number of holes \(n_h\) and the intrinsic carrier concentration \(n_i\) are related by
सही उत्तर:C. \(n_e=n_h=n_i\)
Each thermally freed electron leaves one hole, so \(n_e=n_h=n_i\).
25
The total current \(I\) in a semiconductor, in terms of the electron current \(I_e\) and the hole current \(I_h\), is
सही उत्तर:A. \(I=I_e+I_h\)
Electrons and holes both contribute, so the currents add: \(I=I_e+I_h\).
26
Under an applied electric field, holes move towards the
सही उत्तर:C. negative potential
Holes behave as positive charges, so they move towards the negative potential.
27
In a capacitor input filter, the time constant is
सही उत्तर:B. \(CR_L\)
The rate of fall of the capacitor voltage depends inversely on the product \(CR_L\), which is the time constant.
28
An intrinsic semiconductor at \(T=0\ \text{K}\) behaves like
सही उत्तर:D. an insulator
At \(0\ \text{K}\) there are no electrons in the conduction band, so an intrinsic semiconductor behaves like an insulator.
29
Carbon, silicon and germanium have the same lattice structure, yet carbon is an insulator. The reason is that
सही उत्तर:C. the bonding electrons of carbon lie in the second orbit, so its energy gap is highest and free electrons are negligible
The energy needed to free a bonding electron is highest for C, followed by Si and then Ge, so carbon has negligible free electrons.
30
The energy gap of silicon is
सही उत्तर:B. \(1.1\ \text{eV}\)
The energy gaps of C, Si and Ge are \(5.4\ \text{eV}\), \(1.1\ \text{eV}\) and \(0.7\ \text{eV}\) respectively.
31
Tin (Sn) is a group IV element, but it is a metal because its energy gap is
सही उत्तर:D. \(0\ \text{eV}\)
Sn has zero energy gap, so its bands overlap and it behaves as a metal.
32
Carbon, silicon and germanium have four valence electrons each. Which statement about their energy gaps is true?
सही उत्तर:A. \((E_g)_{\text{C}}>(E_g)_{\text{Si}}>(E_g)_{\text{Ge}}\)
The gaps are \(5.4\ \text{eV}\) for C, \(1.1\ \text{eV}\) for Si and \(0.7\ \text{eV}\) for Ge, so \((E_g)_{\text{C}}>(E_g)_{\text{Si}}>(E_g)_{\text{Ge}}\).
33
The deliberate addition of a desirable impurity to a pure semiconductor is called
सही उत्तर:B. doping
Adding a suitable impurity on purpose is called doping, and the impurity atoms are called dopants.
34
Adding a few parts per million of a suitable impurity to a pure semiconductor changes its conductivity
सही उत्तर:A. manifold, increasing it greatly
A few ppm of dopant increases the conductivity manifold, giving an extrinsic semiconductor.
35
A necessary condition for a dopant to fit into the semiconductor lattice without distorting it is that
सही उत्तर:D. the sizes of the dopant and the semiconductor atoms should be nearly the same
The dopant should have nearly the same size as the host atom so that it occupies a lattice site without distortion.
36
According to Exercise 14.5, when a forward bias is applied to a p-n junction, it
सही उत्तर:C. lowers the potential barrier
Forward bias reduces the barrier height to \(V_0-V\), which allows a large majority carrier current.
37
Which of the following are trivalent dopants used in Si or Ge?
सही उत्तर:A. Boron, aluminium and indium
Boron, aluminium and indium have valency 3 and act as acceptors.
38
In an n-type silicon crystal, which statement is true?
सही उत्तर:D. Holes are minority carriers and pentavalent atoms are the dopants
Pentavalent dopants make electrons the majority carriers and holes the minority carriers.
39
In a p-type semiconductor
सही उत्तर:C. holes are the majority carriers and the dopants are trivalent atoms
Trivalent acceptors create holes, so holes are majority carriers and \(n_h\gg n_e\).
40
The energy needed to set free the fifth electron of a pentavalent donor in silicon is about
सही उत्तर:B. \(0.05\ \text{eV}\)
About \(0.05\ \text{eV}\) is needed for silicon, far less than the \(1.1\ \text{eV}\) band gap.
41
A rectifier uses a capacitor input filter. Its output voltage is nearer to the
सही उत्तर:C. peak voltage of the rectified output
The capacitor charges to the peak value and discharges slowly through the load, so the output stays close to the peak voltage.
42
When \(E_C\) and \(E_V\) are drawn as straight lines in an energy band diagram, they should be taken respectively as
सही उत्तर:D. the bottom of the conduction band energy levels and the top of the valence band energy levels
Energy bands are delocalised, so \(E_C\) is the bottom of the conduction band and \(E_V\) is the top of the valence band.
43
The energy needed to separate the fifth electron of a donor atom in germanium is about
सही उत्तर:A. \(0.01\ \text{eV}\)
The donor ionisation energy is about \(0.01\ \text{eV}\) for germanium.
44
In an n-type semiconductor, the holes are present only because of
सही उत्तर:B. intrinsic thermal generation
Donors supply only electrons, so the holes come from intrinsic generation, and recombination reduces them further.
45
In n-type semiconductors, the electron and hole concentrations are related by
सही उत्तर:D. \(n_e\gg n_h\)
Donor electrons make \(n_e\gg n_h\) in an n-type semiconductor.
46
In compound semiconductors such as GaAs, the type of semiconductor can also be changed by changing the
सही उत्तर:B. relative stoichiometric ratio of the constituents
For example, Ga-rich or As-rich GaAs (such as \(\text{Ga}_{1.1}\text{As}_{0.9}\)) differs from the ideal 1:1 ratio, which changes the semiconductor type.
47
Does an extrinsic semiconductor carry a net charge?
सही उत्तर:A. No, it is neutral because the charge of the additional carriers equals and is opposite to that of the ionised cores
The crystal maintains overall charge neutrality, since the extra carriers are balanced by the ionised dopant cores.
48
In the energy band diagram of an n-type semiconductor, the donor energy level \(E_D\) lies
सही उत्तर:C. slightly below the bottom \(E_C\) of the conduction band
\(E_D\) lies about \(0.01\ \text{eV}\) below \(E_C\), so donor electrons easily enter the conduction band.
49
In the energy band diagram of a p-type semiconductor, the acceptor level \(E_A\) lies
सही उत्तर:A. slightly above the top \(E_V\) of the valence band
\(E_A\) is slightly above \(E_V\), so valence electrons can easily jump to it and leave holes.
50
In thermal equilibrium, the electron concentration \(n_e\) and hole concentration \(n_h\) are related to \(n_i\) by
सही उत्तर:B. \(n_en_h=n_i^2\)
The mass-action relation \(n_en_h=n_i^2\) holds for both intrinsic and extrinsic semiconductors.
51
A pure Si crystal has \(5\times10^{28}\ \text{atoms m}^{-3}\) and is doped with 1 ppm of pentavalent As. If \(n_i=1.5\times10^{16}\ \text{m}^{-3}\), the hole concentration is about
सही उत्तर:C. \(4.5\times10^{9}\ \text{m}^{-3}\)
\(n_e\approx5\times10^{22}\ \text{m}^{-3}\), so \(n_h=\dfrac{n_i^2}{n_e}=\dfrac{2.25\times10^{32}}{5\times10^{22}}=4.5\times10^{9}\ \text{m}^{-3}\).
52
A pure Si crystal has \(5\times10^{28}\ \text{atoms m}^{-3}\) and is doped with 1 ppm of pentavalent As. The electron concentration is approximately
सही उत्तर:D. \(5\times10^{22}\ \text{m}^{-3}\)
1 ppm means \(10^{-6}\times5\times10^{28}=5\times10^{22}\ \text{m}^{-3}\) donors, and thermally generated electrons are negligible in comparison.
53
Two important processes that occur during the formation of a p-n junction are
सही उत्तर:C. diffusion and drift
Carriers diffuse across the junction because of the concentration gradient, and the resulting field causes drift.
54
In an unbiased p-n junction, holes diffuse from the p-region to the n-region because
सही उत्तर:A. the hole concentration in the p-region is higher than in the n-region
Carriers diffuse from a region of higher concentration to lower concentration.
55
When electrons diffuse from the n-side to the p-side, they leave behind ionised donors that form
सही उत्तर:D. a positive space-charge region on the n-side
Ionised donors are immobile positive ions, which build a positive space-charge layer on the n-side.
56
The thickness of the depletion region in a p-n junction is of the order of
सही उत्तर:B. \(0.1\ \mu\text{m}\)
The depletion region is about one-tenth of a micrometre thick.
57
The electric field in the depletion region of a p-n junction is directed
सही उत्तर:D. from the n-side towards the p-side
The field points from the positive space charge on the n-side to the negative space charge on the p-side.
58
In a p-n junction, the direction of the drift current is
सही उत्तर:C. opposite to that of the diffusion current
The drift current, due to the built-in field, opposes the diffusion current.
59
A p-n junction in equilibrium has
सही उत्तर:B. a diffusion current equal to the drift current, so there is no net current
The depletion region grows until the diffusion and drift currents balance.
60
The built-in barrier potential across an unbiased p-n junction opposes
सही उत्तर:A. the movement of electrons from the n-region into the p-region
The n-material becomes positive relative to the p-material, so the potential prevents electrons moving from n to p.
61
Why can a p-n junction not be made by simply pressing a p-type slab against an n-type slab?
सही उत्तर:B. Any slab has roughness much larger than the inter-atomic spacing, so continuous contact at the atomic level is impossible
The junction would behave as a discontinuity for the flowing charge carriers.
62
The small, almost constant current in a diode under reverse bias is called the
सही उत्तर:C. reverse saturation current
Under reverse bias the current is of the order of \(\mu\text{A}\) and almost independent of bias, so it is the reverse saturation current.
63
If the current through a diode exceeds the rated value specified by the manufacturer, the diode
सही उत्तर:A. gets destroyed due to overheating
Excess current, in forward or reverse bias, destroys the diode by overheating.
64
A p-n junction diode is forward biased when
सही उत्तर:D. the p-side is connected to the positive terminal and the n-side to the negative terminal
By definition, forward bias connects the p-side to the positive and the n-side to the negative terminal.
65
Under forward bias of voltage \(V\), the effective barrier height of a p-n junction with built-in potential \(V_0\) is
सही उत्तर:A. \(V_0-V\)
The applied voltage opposes the built-in potential, so the barrier becomes \(V_0-V\).
66
Under reverse bias of voltage \(V\), the effective barrier height of a p-n junction with built-in potential \(V_0\) is
सही उत्तर:D. \(V_0+V\)
The applied voltage adds to the built-in potential, so the barrier becomes \(V_0+V\).
67
When a p-n junction is forward biased, the width of the depletion layer
सही उत्तर:C. decreases
Forward bias reduces the barrier and narrows the depletion layer.
68
When a p-n junction is reverse biased, the depletion region
सही उत्तर:B. becomes wider
Reverse bias raises the barrier and widens the depletion region.
69
The reverse breakdown voltage of a diode used in a rectifier must be
सही उत्तर:D. sufficiently higher than the peak ac voltage at the secondary of the transformer
This protects the diode from reverse breakdown during the negative half cycle.
70
The magnitude of the forward current in a p-n junction diode is usually of the order of
सही उत्तर:C. \(\text{mA}\)
Forward current due to injected carriers is usually in mA.
71
The reverse current in a p-n junction diode is usually of the order of a few
सही उत्तर:B. \(\mu\text{A}\)
Reverse current is due only to minority carriers, so it is of the order of a few \(\mu\text{A}\).
72
The reverse current in a diode, below breakdown, is limited by
सही उत्तर:A. the concentration of minority carriers on either side of the junction
Even a small voltage sweeps all minority carriers across, so the current depends on their concentration and not on the voltage.
73
The breakdown voltage \(V_{br}\) of a diode is
सही उत्तर:C. the critical reverse bias voltage at which the reverse current increases sharply
At \(V=V_{br}\) the reverse current rises sharply for a slight increase in bias.
74
The threshold (cut-in) voltage of a silicon diode is about
सही उत्तर:C. \(0.7\ \text{V}\)
Silicon diodes start conducting significantly at about \(0.7\ \text{V}\).
75
The threshold (cut-in) voltage of a germanium diode is about
सही उत्तर:D. \(0.2\ \text{V}\)
Germanium diodes have a cut-in voltage of about \(0.2\ \text{V}\).
76
The dynamic resistance \(r_d\) of a diode is defined as
सही उत्तर:A. \(\dfrac{\Delta V}{\Delta I}\)
Dynamic resistance is the ratio of a small change in voltage to the corresponding small change in current.
77
On the forward characteristic of a silicon diode, \(I=10\ \text{mA}\) at \(V=0.7\ \text{V}\) and \(I=20\ \text{mA}\) at \(V=0.8\ \text{V}\). The forward resistance is