Are you looking for JAC Class 12 Physics Chapter 3 “Current Electricity” MCQs (Objective Questions) with Answers? You are at the right place! On JAC Exam Prep, you will find important Multiple Choice Questions (MCQs) with Answers from the “Current Electricity” chapter. These questions are prepared according to the latest NCERT syllabus and with a focus on the Jharkhand Academic Council (JAC) examination.
These Current Electricity MCQs cover important topics such as electric current, drift velocity, mobility, Ohm’s law, resistance, resistivity, conductivity, temperature dependence of resistance, combinations of resistors, electromotive force (EMF), internal resistance, cells in series and parallel, Kirchhoff’s rules, Wheatstone bridge, and electrical power. By practising these questions, students can revise the chapter effectively, strengthen their conceptual understanding, and perform better in the JAC Class 12 Annual Examination.
Compared with the typical thermal speed of copper atoms at ordinary temperature, the drift speed of electrons is smaller by a factor of about:
सही उत्तर:B. 10⁻⁵
Example 3.1 gives a thermal speed of about 2 × 10² m/s against a drift speed of about 10⁻³ m/s, a ratio of about 10⁻⁵.
26
Why does current get established almost instantly when a circuit is closed even though the drift speed is only a few mm/s?
सही उत्तर:B. The electric field is established throughout the circuit almost instantly (with the speed of light)
The field causes local electron drift at every point, so there is no need to wait for electrons to travel the whole conductor.
27
Electrons in a conductor acquire a steady average drift speed instead of continuous acceleration because:
सही उत्तर:B. Of repeated collisions with the positive ions
An electron speeds up until it collides with an ion, loses its drift speed, and then starts again, so on average only a drift speed is acquired.
28
Large currents are obtained in a conductor despite the small drift speed because:
सही उत्तर:C. The electron number density is enormous (~10²⁹ m⁻³)
I = neAvd is large because n is very large.
29
When electrons drift in a metal from lower to higher potential:
सही उत्तर:B. The drift velocity is superposed over the large random velocities
The drift is a small net velocity added to the large random thermal motion.
30
The paths of electrons between successive collisions are:
सही उत्तर:D. Straight without a field and, in general, curved with a field
Without a field the paths are straight lines. With a field the electrons are accelerated, so the paths are in general curved.
31
Mobility μ of a charge carrier is defined as:
सही उत्तर:A. Drift velocity per unit electric field
μ = |vd|/E, and mobility is positive.
32
The SI unit of mobility is:
सही उत्तर:B. m² V⁻¹ s⁻¹
μ = vd/E has units (m/s)/(V/m) = m²/(V s).
33
The mobility of electrons in a conductor is given by:
सही उत्तर:C. μ = eτ/m
μ = vd/E = eτ/m, where τ is the average collision time.
34
Which of the following devices does NOT obey Ohm's law because V-I relation depends on the sign of V?
सही उत्तर:C. Diode
In a diode, reversing the direction of V does not produce a current of the same magnitude in the opposite direction.
35
Which material shows more than one value of V for the same current I?
सही उत्तर:B. GaAs
GaAs shows a non-unique V-I relation, with a negative resistance region.
36
The resistivities of metals lie roughly in the range:
सही उत्तर:A. 10⁻⁸ Ω m to 10⁻⁶ Ω m
Metals have low resistivities, while insulators are 10¹⁸ times greater or more.
37
With a rise in temperature, the resistivity of a semiconductor:
सही उत्तर:C. Decreases
In semiconductors, n increases with temperature, which more than compensates for the decrease in τ.
38
The temperature coefficient of resistivity α has the dimensions of:
सही उत्तर:B. (Temperature)⁻¹
From ρT = ρ₀[1 + α(T − T₀)], α has units of (temperature)⁻¹.
39
For metals, the temperature coefficient of resistivity α is:
सही उत्तर:C. Positive
The resistivity of metals increases with temperature.
40
The resistivity of a metal increases with temperature mainly because:
सही उत्तर:B. The relaxation time τ decreases due to more frequent collisions
In a metal n is nearly temperature independent, while τ decreases with temperature, so ρ = m/(ne²τ) increases.
41
Why does the resistivity of insulators and semiconductors decrease with temperature?
सही उत्तर:C. The number density n of carriers increases and more than compensates the decrease in τ
The increase in n with temperature outweighs the decrease in τ.
42
Nichrome, manganin and constantan are used in wire-bound standard resistors because:
सही उत्तर:B. Their resistivity depends only weakly on temperature
Their resistance values change very little with temperature.
43
In Example 3.3, a nichrome element has resistance 75.3 Ω at 27.0 °C and 85.8 Ω at the steady state (α = 1.70 × 10⁻⁴ °C⁻¹). The steady temperature is approximately:
सही उत्तर:D. 847 °C
T₂ − T₁ = (85.8 − 75.3)/(75.3 × 1.70 × 10⁻⁴) ≈ 820 °C, so T₂ = 847 °C.
44
A platinum thermometer has R₀ = 5 Ω at the ice point, R₁₀₀ = 5.23 Ω at the steam point and 5.795 Ω in a hot bath. The temperature of the bath is:
सही उत्तर:C. 345.65 °C
t = [(5.795 − 5)/(5.23 − 5)] × 100 = 345.65 °C.
45
The power dissipated as heat in a conductor carrying current I at a potential difference V is:
सही उत्तर:C. P = IV
The energy dissipated in Δt is ΔW = IVΔt, so P = IV.
46
The ohmic power loss in a resistor R can be written as:
सही उत्तर:A. P = I²R = V²/R
Using V = IR in P = IV gives P = I²R = V²/R.
47
To deliver a power P through transmission cables of resistance R_c at voltage V, the power wasted in the cables is:
सही उत्तर:B. P_c = P² R_c/V²
P_c = I²R_c with I = P/V gives P_c = P²R_c/V².
48
Power is transmitted at very high voltage mainly to:
सही उत्तर:C. Reduce the power loss in the transmission cables
Since P_c ∝ 1/V², a high transmission voltage greatly reduces the wasted power. A transformer later lowers the voltage for safe use.
49
The emf of a cell is the potential difference between its positive and negative electrodes when:
सही उत्तर:C. No current is flowing (open circuit)
In an open circuit, ε = V₊ + V₋ is the potential difference between P and N.
50
Which statement about emf is correct?
सही उत्तर:B. It is a potential difference, not a force
The name emf is historical. It is actually a potential difference (work per unit charge).
51
The terminal voltage of a cell of emf ε and internal resistance r delivering current I is:
सही उत्तर:B. V = ε − Ir
V = V₊ + V₋ − Ir = ε − Ir.
52
The current in a circuit with a cell (emf ε, internal resistance r) connected to an external resistance R is:
सही उत्तर:D. I = ε/(R + r)
From IR = ε − Ir we get I = ε/(R + r).
53
The maximum current that can be drawn from a cell of emf ε and internal resistance r is:
सही उत्तर:B. ε/r
Maximum current occurs at R = 0, so I_max = ε/r.
54
Two cells of emfs ε₁, ε₂ and internal resistances r₁, r₂ are connected in series (positive of one joined to negative of other). The equivalent emf and internal resistance are:
सही उत्तर:A. ε₁ + ε₂ and r₁ + r₂
In series the emfs add and the internal resistances add.
55
If two cells are connected in series with their negative terminals joined (ε₁ > ε₂), the equivalent emf is:
सही उत्तर:C. ε₁ − ε₂
The emf of the cell through which current leaves from the negative electrode enters with a negative sign.
56
For two cells connected in parallel, the equivalent internal resistance is:
सही उत्तर:B. r₁r₂/(r₁ + r₂)
1/r_eq = 1/r₁ + 1/r₂, so r_eq = r₁r₂/(r₁ + r₂).
57
For n cells connected in parallel, the equivalent emf ε_eq satisfies:
Kirchhoff's junction rule states that at any junction:
सही उत्तर:B. The sum of currents entering equals the sum of currents leaving
It is based on conservation of charge: there is no accumulation of charge at a junction in steady state.
59
Kirchhoff's loop rule states that:
सही उत्तर:C. The algebraic sum of changes in potential around any closed loop is zero
Coming back to the starting point, the total change in electric potential must be zero.
60
The balance condition of a Wheatstone bridge (arms R₁, R₂, R₃, R₄, with R₂/R₁ = R₄/R₃) means that:
सही उत्तर:B. The galvanometer shows null deflection (I_g = 0)
At balance there is no current through the galvanometer arm.
61
In a balanced Wheatstone bridge with the unknown resistance R₄ in the fourth arm, R₄ is given by:
सही उत्तर:B. R₃R₂/R₁
From R₂/R₁ = R₄/R₃, R₄ = R₃(R₂/R₁).
62
A battery of 10 V is connected across diagonally opposite corners of a cube made of 12 resistors, each of R. The equivalent resistance is:
सही उत्तर:A. 5R/6
Using symmetry and Kirchhoff's rules, ε = (5/2)IR with total current 3I, so R_eq = ε/3I = 5R/6.
63
In the cube network of Example 3.5 (R = 1 Ω, ε = 10 V), the total current drawn is 12 A. The current in each of the three edges leaving the corner A is:
सही उत्तर:D. 4 A
The total 3I = 12 A, so I = 4 A in each of the edges AA′, AD and AB.
64
In the network of Example 3.6, the current in branch CD is:
सही उत्तर:B. 0 A
Solving the three Kirchhoff equations gives I₁ = 2.5 A, I₂ = 5/8 A, I₃ = 1 7/8 A, and the current in CD is 0 A.
65
In Example 3.7 (Wheatstone bridge with AB = 100 Ω, BC = 10 Ω, CD = 5 Ω, DA = 60 Ω, galvanometer of 15 Ω across BD, 10 V across AC), the galvanometer current is:
सही उत्तर:A. 4.87 mA
Solving the mesh equations gives 410.5 I_g = 2, so I_g ≈ 4.87 mA.
66
The storage battery of a car has emf 12 V and internal resistance 0.4 Ω. The maximum current that can be drawn is:
सही उत्तर:B. 30 A
I_max = ε/r = 12/0.4 = 30 A.
67
A battery of emf 10 V and internal resistance 3 Ω is connected to a resistor and the current is 0.5 A. The resistance of the resistor is:
सही उत्तर:D. 17 Ω
R + r = ε/I = 10/0.5 = 20 Ω, so R = 17 Ω.
68
For the same circuit (ε = 10 V, r = 3 Ω, I = 0.5 A), the terminal voltage of the battery is:
सही उत्तर:B. 8.5 V
V = ε − Ir = 10 − 0.5 × 3 = 8.5 V.
69
The resistance of a heating element is 100 Ω at 27.0 °C and 117 Ω at a higher temperature (α = 1.70 × 10⁻⁴ °C⁻¹). The higher temperature is:
सही उत्तर:A. 1027 °C
ΔT = 17/(100 × 1.70 × 10⁻⁴) = 1000 °C, so T = 27 + 1000 = 1027 °C.
70
A wire of length 15 m and cross-section 6.0 × 10⁻⁷ m² has a resistance of 5.0 Ω. Its resistivity is:
सही उत्तर:A. 2 × 10⁻⁷ Ω m
ρ = RA/l = (5.0 × 6.0 × 10⁻⁷)/15 = 2 × 10⁻⁷ Ω m.
71
A silver wire has resistance 2.1 Ω at 27.5 °C and 2.7 Ω at 100 °C. Its temperature coefficient of resistivity is approximately:
A nichrome heating element on a 230 V supply draws an initial current of 3.2 A that settles to 2.8 A (room temperature 27.0 °C, α = 1.70 × 10⁻⁴ °C⁻¹). The steady temperature is approximately:
सही उत्तर:B. 867 °C
R₁ = 230/3.2 = 71.9 Ω and R₂ = 230/2.8 = 82.1 Ω, so ΔT ≈ 840 °C and T₂ ≈ 867 °C.
73
In the network of Fig. 3.20 (Exercise 3.7: 10 V battery in series with 10 Ω, bridge with AB = 10 Ω, BC = 5 Ω, AD = 5 Ω, DC = 10 Ω, BD = 5 Ω), the total current drawn from the battery is:
सही उत्तर:A. 10/17 A
The bridge has an equivalent resistance of 7 Ω, so the total resistance is 17 Ω and I = 10/17 A.
74
In the same network (Fig. 3.20), the current in the branch AB (10 Ω) is:
सही उत्तर:D. 4/17 A
Solving the node equations gives I_AB = 4/17 A, I_AD = 6/17 A, and 2/17 A flows through BD from D to B.
75
A storage battery of emf 8.0 V and internal resistance 0.5 Ω is charged by a 120 V dc supply through a series resistor of 15.5 Ω. The terminal voltage of the battery during charging is:
सही उत्तर:D. 11.5 V
I = (120 − 8)/(15.5 + 0.5) = 7 A, so V = ε + Ir = 8 + 7 × 0.5 = 11.5 V.
76
What is the purpose of the series resistor in the battery-charging circuit of Exercise 3.8?
सही उत्तर:B. To limit the current drawn from the supply
Without the resistor, the large 120 V supply would drive an excessive current through the low-resistance battery.
77
An electron in a copper wire (n = 8.5 × 10²⁸ m⁻³, A = 2.0 × 10⁻⁶ m², I = 3.0 A) takes how long to drift along a 3.0 m length?
सही उत्तर:A. About 2.7 × 10⁴ s
vd = I/(neA) ≈ 1.1 × 10⁻⁴ m/s, so t = 3.0/(1.1 × 10⁻⁴) ≈ 2.7 × 10⁴ s (about 7.5 hours).
78
In a neutral current-carrying wire, the net charge density ρ is:
सही उत्तर:B. Zero
ρ₊ = −ρ₋, so ρ = 0. The relation j = ρv therefore does not apply to the total charge density, and j = ρ₋v₋.
79
According to Points to Ponder, the equation V = IR:
सही उत्तर:C. Defines resistance and can be applied to all conducting devices
Ohm's law actually asserts that the plot of I versus V is linear, i.e., R is independent of V.
80
Insulators like glass and rubber have resistivity greater than that of metals by a factor of about:
सही उत्तर:D. 10²² to 10²⁴
The Summary states that insulators like glass and rubber have 10²² to 10²⁴ times greater resistivity than metals.